tooth depth
英 [tuːθ depθ]
美 [tuːθ depθ]
网络 齿全高; 齿高
双语例句
- Also, the construction and the work principle of the electronic optical comparator which serves as an instrument of high precision in measuring the wear all over the tooth profile is introduced as well as the principle and calculation in radioactive determination of the wear in tooth depth.
同时，文中还介绍了精密测量全齿廓磨损的光电比较仪的结构和原理，以及放射性测定齿长磨损的原理和计算方法。 - A quadratic model of predicting helical milling force was researched. The effects of spindle speed, feed per tooth, and axial and radial depth of cut were analyzed.
通过统计学中的响应曲面法建立了螺旋铣削过程中切削力的二阶模型，并分析了主轴转速、每齿进给量、轴向和径向切削深度等因素对切削力的影响。 - The interaction of feed per tooth and depth of cut introduces a lower frequency periodic signal;
铣削深度和每齿进给量之间的交互作用在切削力响应信号中表现为低频周期信号； - The equation of meshing, control equation of the tooth depth and the second order geometric parameters of the gear tooth surface are established.
推导出相应的切齿啮合方程、工件齿面二阶参数展成控制方程和工件齿深控制方程，并给出机床运动函数、刀盘中心速度以及刀尖半径的具体求解方法。 - The cutting force and vibration of different machining conditions have been studied. The results show that effect of cutting speed on cutting force and vibration is more unremarkable than feed per tooth and cutting depth.
通过对不同切削条件下切削力和振动进行分析，发现切削速度的增加不会引起切削力和振动较大变化，而每齿进给量和轴向切深对切削力和振动的影响较大。 - Study on Micro-hardness and Wear Resistance of Human Tooth at Different Depth
人体天然牙不同深度层次的显微硬度与耐磨性的研究 - After studying a few measuring methods of the hobbing depth of large diameter circular-arc gear, measuring the full tooth depth should be the best way.
通过对目前圆弧齿轮切齿深度常用的几种测量方法的比较，提出了大直径圆弧齿轮切齿深度的控制最好采用检测全齿深这一方法。 - The micro-wear test results show that main wear mechanisms of the swine tooth enamel and the human tooth enamel are both delamination and plough. The steady-state friction coefficient and the largest wear depth of the swine tooth enamel are greater than that of human tooth enamel. 4.
宏观摩擦试验结果表明，猪牙釉质和人牙釉质的磨损机制类似，剥落和犁沟共存于二者的磨斑表面，猪牙釉质的稳态摩擦系数和最大磨损深度均大于人牙釉质。 - The transient stress distribution along the breadth of the tooth and depth of tooth and the influence of profile modification were further studied.
在此基础上，对沿轮齿齿宽和齿高方向的瞬态应力分布情况以及修形对啮合瞬态性能的影响进行了较为详细的分析。 - To evaluate the default effects under identical loading condition on the vibration responses, two types of defects are incorporated in these 3D models for simulation: crack at the tooth foot with different depth and spalling at the tooth flank with various sizes.
为研究和评价在相同载荷下不同齿轮故障对传动系统的振动响应的影响，对两种类型的齿轮故障进行三维建模和仿真：齿根处不同厚度的裂纹和齿面不同尺寸的剥落。 - First the transient temperature fields in tooth surface by pulsed line-source laser producing are studied. The temperature rises in the direction of depth and the radius are analyzed.
先讨论了激光线源作用于牙齿表面时产生的瞬态温度场，得到了深度和光斑半径方向上的温升情况。 - Experimental results show that the order of importance of three factors affecting milling force: feed per tooth, radial depth of cut, cutting speed. Improved milling finite element simulation results, compared with the experimental data, the trend is the same.
铣削试验结果表明影响铣削力大小的三因素的重要性顺序为：每齿进给量、径向切深、切削速度；改进的铣削有限元仿真结果与实验数据对比，表明变化趋势是一致的。 - Were to change the amount of feed per tooth, cutting depth, cutting width, cutting speed, the four cutting parameters of single-factor experiments. The data obtained by experiment and simulation results were analyzed. 3.
分别改变每齿进给量、切削深度、切削宽度、切削速度这四个切削参数进行单因素切削试验，通过试验得到的数据与仿真结果进行对比验证。